NJ Fishing Advertise Here at New Jersey's Number 1 Fishing Website!


Message Board


Zinc Replacement - NJFishing.com Your Best Online Source for Fishing Information in New Jersey


Message Board Registration       FAQ

Go Back   NJFishing.com Your Best Online Source for Fishing Information in New Jersey > NJFishing.com Boating
FAQ Members List Calendar Mark Forums Read

NJFishing.com Boating Use this board to discuss anything related to boats and boating in NJ

Reply
 
Thread Tools Display Modes
  #1  
Old 05-10-2009, 03:29 PM
Flukemeister1 Flukemeister1 is offline
NJFishing.com Ambassador
 
Join Date: Mar 2008
Posts: 480
Default Zinc Replacement

How badly corroded do zincs have to get before you have to replace them? Is a mild to moderate amount of corrosion ok or should they be swapped out at the first sign of deterioration?

Thanks in advance for your advice,

Doc
Reply With Quote
  #2  
Old 05-10-2009, 03:35 PM
Gerry Zagorski's Avatar
Gerry Zagorski Gerry Zagorski is offline
Owner NJFishing.com
 
Join Date: Mar 2008
Location: Edison, NJ
Posts: 11,037
Default Re: Zinc Replacement

You want to replace them when they are about half way gone.

Clipped from Boats US site:
Sacrificial Zincs
by Don Casey

Any time you have two different metals that are physically or electrically connected and immersed in seawater, they become a battery. Some amount of current flows between the two metals. The electrons that make up that current are supplied by one of the metals giving up bits of itself-in the form of metal ions-to the seawater. This is called galvanic corrosion and, left unchecked, it quickly destroys underwater metals.
The most common casualty of galvanic corrosion is a bronze or aluminum propeller on a stainless steel shaft, but metal struts, rudders, rudder fittings, outboards, and stern drives are also at risk. The way we counteract galvanic corrosion is to add a third metal into the circuit, one that is quicker than the other two to give up its electrons. This piece of metal is called a sacrificial anode, and most often it is zinc. In fact, most boaters refer to sacrificial anodes simply as zincs.
It would be hard to overstate the importance of maintaining the zinc anodes on your boat. When a zinc is gone, the metal component it was installed to protect begins to dissolve-guaranteed.
How much zinc
The amount of protection a zinc anode provides depends on its surface area. The zinc surface area needed varies with the kind of metal being protected and with the chemical make-up of the water, but you can use 1% of the surface area of the protected metal as a starting point. Check the protected metal frequently. If it shows signs of corrosion despite the zinc, you need more surface area.

Zincs should be replaced when about half of the anode has been lost to corrosion. Ideally we want that to occur not more frequently than annually. The longevity of a sacrificial zinc anode is a function of its weight. When a zinc lasts less than a year, you need one with more weight.
Normally, however, you are not faced with determining the appropriate anode size (other than diameter for a zinc shaft collar). Rather, you are simply replacing depleted zincs with new ones of the same size. Check all zincs at least annually and replace all that are half depleted. Here are some replacement guidelines.
Electrical contact is essential
There is an unfortunate misconception that a sacrificial anode can be mounted anywhere, even hung over the side on a string, and it will still perform its appointed duty. That is dead wrong!

For a zinc anode to provide any protection, it must be in electrical contact with the metal being protected. The conductivity of the water is not adequate. We need low-resistance, metal-to-metal contact-either by mounting the zinc directly to the metal being protected or by con- necting the two with a wire. A hanging anode can provide protection if it is connected by a wire to the metal being protected.
Where the zinc is mounted directly to the protected metal-bolted to the side of a metal rudder, for example-it is essential to make sure the surface under the zinc is bare and bright before the anode is installed. This is to ensure good electrical contact.
No paint
Zinc anodes cannot perform their function unless they are exposed. Putting paint on a zinc smothers it, rendering it useless. Never coat zinc anodes with bottom paint, or anything else.

Props and rudders
Propellers are normally protected by a zinc collar fashioned in two pieces and bolted together around the shaft forward of the propeller. It is essential to make sure the shaft is clean and bright before clamping the collar to it. Corrosion protection for outboard and outdrive propellers is typically provided by a bolt-in-place zinc ring or a zinc prop nut.

Metal rudders and struts are most easily protected with zinc disks bolted directly to the metal. Rudder zincs have a shallow dome shape to streamline them and minimize their drag and turbulence.
Hull plates
Bonding is a different subject altogether, but boats with all underwater fittings bonded together electrically are typically fitted with one or more zinc plates bolted to the hull. The mounting bolts for these anodes are connected by heavy-gauge electrical cable to the bonding circuit. If these anodes are allowed to deplete or if the electrical connection deteriorates, other underwater metal, such as bronze through-hull fittings, will begin to corrode.

Zinc hull plates are also fitted to metal boats to protect the hull. Needless to say, such anodes must be carefully monitored.
Outdrives
The mix of immersed metals makes stern drives and outboards particularly prone to galvanic corrosion. Many are fitted with multiple anodes. Typically, these include at a minimum a sacrificial trim tab (intended to warn you of depletion by a change in steering), a zinc plate or two attached to the gear case or the anti-ventilation plate, and perhaps anodes in the exhaust cavity and in the cooling-water jacket. It is a good idea to consult your engine manual to be sure you know where every anode is located. Then check all of them and renew any that are more than half depleted.

Zinc pencils
Heat exchangers, because they are typically a copper alloy, are at risk of galvanic corrosion. To combat this, most heat exchangers are fitted with a zinc "pencil" anode. You will find it (or not) under a brass plug in the exchanger. The pencil is unscrewed from the plug for replacement. Some engines have a similar zinc pencil inside the cooling-water jacket to protect dissimilar metals in the engine. Determine if your engine and heat exchanger are fitted with internal anodes, and if so, check them at least annually. If they are half depleted. . .well, you know.
For more guidance on maintaining your boat, consult This Old Boat by Don Casey
__________________

Gerry Zagorski <><

Founder/Owner of NJFishing.com since 1997
Proud Supporter of Heroes on the Water
NJFishing@aol.com
Obsession
28 Carolina Classic
Sandy Hook Area

Last edited by Gerry Zagorski; 05-10-2009 at 03:39 PM..
Reply With Quote
  #3  
Old 05-10-2009, 03:36 PM
Flukemeister1 Flukemeister1 is offline
NJFishing.com Ambassador
 
Join Date: Mar 2008
Posts: 480
Default Re: Zinc Replacement

That's about where it is now. Thanks.
Reply With Quote
  #4  
Old 05-10-2009, 04:41 PM
CaptBob's Avatar
CaptBob CaptBob is offline
NJFishing.com Old Salt
 
Join Date: Mar 2008
Posts: 1,369
Default Re: Zinc Replacement

Make sure you clean the area under the zinc so you have bare metal on bare metal
Reply With Quote
  #5  
Old 05-10-2009, 08:10 PM
Flukemeister1 Flukemeister1 is offline
NJFishing.com Ambassador
 
Join Date: Mar 2008
Posts: 480
Default Re: Zinc Replacement

I did not know about the importance of the metal to metal contact. The anode that is shot is on the lower unit. A few years ago I installed additional zincs on my trim tabs when I noticed them starting to pit and those zincs have shown little wear. The info that you can get on this site is amazing and most appreciated. It makes taking care of your boat the right way easy as pie.
Reply With Quote
  #6  
Old 05-10-2009, 08:20 PM
CaptBob's Avatar
CaptBob CaptBob is offline
NJFishing.com Old Salt
 
Join Date: Mar 2008
Posts: 1,369
Default Re: Zinc Replacement

Anodes (zincs) should come into contact with the metal part it will protect, and the potential of any sacrificial anode needs to be at least 200 milliamps higher than the other metal components. Without metal to metal contact you risk having damage done, some anodes are connected by a ground wire as on a lower unit, etc.

Last edited by CaptBob; 05-10-2009 at 08:23 PM..
Reply With Quote
  #7  
Old 05-10-2009, 10:53 PM
River Rat's Avatar
River Rat River Rat is offline
Moderator
 
Join Date: Mar 2008
Posts: 789
Default Re: Zinc Replacement

Best prices on zincs I found was from EBasicPower.com

Probably 1/2 the price of local boating store.... UPS delivers to Jersey in 2 days
__________________
South River Boat Club
27' SR Amberjack
"Angry Beaver"
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 02:04 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.